| Subject | Date Asked | Expert |
|
| 91 evinrude exp | 8/6/2008 | Everett Peacock |
Q: i looks like i have water mixing with fuel after the fuel runs through my VRO pump?{turns milky} ...
A: where the VRO pump connects to the block or crankcase there is a check valve, it is ussaly brass. ...
|
| Fuel leakage | 8/3/2008 | Everett Peacock |
Q: I have a 1979 140hp outboard Evinrude. When the motor is running I have gas shooting out of the ...
A: the needle valves in the carbs are stuck open, pull the carbs off and dissasemble them and clean, ...
|
| Merc 150 Oil/Temp Alarm | 8/3/2008 | Everett Peacock |
Q: Temp/Oil alarm will start beeping at different times during operation...oil tanks are full and motor ...
A: it sounds like the oil pump is failing....run premixed fuel until you find the problem....if you ...
|
| evinrude 33 hp boat motor | 8/1/2008 | Everett Peacock |
Q: I have a 33 hp 1969, boat motor, when i have the boat in the water, i can give it , about half ...
A: ok single line, that is good the older ones had two lines and you had to have a special fuel ...
|
| tilt/trim | 7/29/2008 | Everett Peacock |
Q: I have an 89 sea ray with a 100hp merc o/b. The tilt trim solenoids click and have power leaving ...
A: the solinoids should have 12 volts to the big side of the relay...when activated if it does then ...
|
| 1989 Mercruiser 3.0L cuts out | 7/29/2008 | Everett Peacock |
Q: Early in the season, I experienced engine cutout after a 30 minute drift over a reef. I had run ...
A: does it have points of not I think it does...set at 28 to 30 degrees dwell or an pack of matches ...
|
| 86 mercury 150 xr2 | 7/29/2008 | Everett Peacock |
Q: Everett, I have 0 PSI water pressure at idle, 5 to 7 PSI up to 3000 RPM, and 0 Psi from 3000 to WOT ...
A: picking mt brain I like this one.......ok 1 double check the inpeller, some have seperated fom ...
|
| c115 yamaha 1997 4 cyl question | 7/29/2008 | Everett Peacock |
Q: i have a problem with my 115 yamaha engine, it idles fine and runs fine at the top end, but when i ...
A: You defintly have a fuel problem....Pull both carbs, and inspect, and clean the passages and ...
|
| Deck Replacement | 7/20/2008 | Daniel Patten |
Q: I have a 1988 Citation 19' boat (3.7 ltr Mercruiser I/O) with a fiberglass hull. The deck in the ...
A: [This is 3rd time thru if you have prev. ver. please disregard this., the browzer window times out ...
|
| trim and tilt problem | 5/27/2008 | Everett Peacock |
Q: mercruiser power trim tilt pump. ? Drive will lower but can not trim up using switch no sound from ...
A: sounds like the trim limit switch has gone bad....back at the engine, there are two sets of wires ...
|
| 1986 4 winns trim tab wiring | 5/25/2008 | chris Wethered |
Q: I have a 96 fours winns...there are two wires that go thru the were the motor is bolted on. the ...
A: i thought your boat was in the water! You need to be able to get at the wire terminals to replace ...
|
| tilt/trim | 5/24/2008 | chris Wethered |
Q: The problem I am having is the tilt up/down isn't working. When I press the button all that happens ...
A: you need to do a maintenance overhaul on the wires and trim limiting indicators plus indicator ...
|
| bass boat 17' nitro 125 hp merc | 5/23/2008 | chris Wethered |
Q: bought it a year ago, when i take off it pulls hard right, can a boat be out of alignment? once I ...
A: i think you need to adjust the problem by using the trim tab. This is located on the lower engine ...
|
| 25 hp Mercury 2 stroke | 5/22/2008 | chris Wethered |
Q: This motor is about 4 years old. The last 2 times on the water, I noticed that It was running great ...
A: Have a conversation with a mechanic about the prop. It sounds like your money saving has come back ...
|
| gel coat | 5/22/2008 | chris Wethered |
Q: i have a sail boat with a deep scratch about a foot long o the hull.i was told that it needs to be ...
A: Fiberglass repair kits or gelcoat kits are not expensive in themselves. You are probably getting a ...
|
| 100 hp mercury outboard | 5/21/2008 | chris Wethered |
Q: I have two questions or problems with a 100 hp mercury outboard S/N:OC189024 #1- the engine starts ...
A: #1 List of things to check: fuel tank either empty - hose incorrectly installed - vent ...
|
| Larson 180 SEI Power Steering Problem | 5/21/2008 | chris Wethered |
Q: I have a 2004 Larson 180 SEI with 3.0 Volvo-Penta engine and Volvo-Penta SX and have a power ...
A: Bob, Possibly the trim tab needs adjustment. Keep the distribution of boatload, make sure the ...
|
| Loud beep on a 2000 Johnson 35hp | 5/20/2008 | chris Wethered |
Q: I was out fishing this weekend and when i was trolling, after maybe 10-15minutes suddenly a loud and ...
A: i think the alarm sounds due to a problem with the oil. Johnson uses a variable ratio oiling (VRO) ...
|
| Boat repair | 5/20/2008 | chris Wethered |
Q: I have a 1998 Lund with a 50 HP Johnson, the motor starts and runs great, I have 2 problems. When ...
A: Problem 1 Check the wiring of the ignition - loose connections, corrosion etc Kill Switch - ...
|
| 1990 15 hp. gamefisher outboard | 5/20/2008 | chris Wethered |
Q: I bought this motor as is not runing found out it had no spark so I found 2 coils on the net. sears ...
A: Here's a few ideas and checks: check the fuel supply hose installation is the fuel vent ...
|
| Pontoon Deck | 5/19/2008 | chris Wethered |
Q: My 2005 Palm Beach Pontoon boat has water coming up through the decking in the middle front of the ...
A: What you ought to do is get the boat out of the water and make sure the hull is not damaged. If it ...
|
| 1979 mariner 28e 28hp wont idle | 5/19/2008 | chris Wethered |
Q: cant get it to idle runs good high rpm bt let off and it dies tried cleaning carbs opened fuel ...
A: Your choke is the cause. Follow the service manual instructions, identify the butterfly plate and ...
|
| 88 Bayliner Capri | 5/18/2008 | chris Wethered |
Q: 305 Inboard with outboard drive. Here is the problem: Grinding noise when you engage motor and ...
A: Sorry to reply so late. Take the lower unit off and strip out all the components. If nothing is ...
|
| 15hp evenrude won't start | 5/17/2008 | chris Wethered |
Q: my 15hp evenrude engine wont start i changed the plugs but it still won't start please help.
A: sorry for late reply Have tested the charge in the battery? The problem is in the starter circuit. ...
|
| impeller | 5/16/2008 | chris Wethered |
Q: where is the impeller located,how do i change it and do i need any special tools to do it, the motor ...
A: the impeller is found in the lower casing. You access it by taking the screws off the casing and ...
|
| Prop won't spin | 5/15/2008 | chris Wethered |
Q: I have a '93 4.3 liter Mercruiser with Alpha 1 outdrive. The forward gear will engage and the ...
A: sorry for late response. Yes you need to get the motor out of the water and follow this procedure ...
|
| scout 1994 transom repair | 5/14/2008 | chris Wethered |
Q: i have a 15.3 that has a cracked transom i wnat to fix it mayself where do i start?
A: i'm not familiar with Scouts. However if the transom is fiberglass, then you can fix that with resin ...
|
| boat alarm | 5/14/2008 | chris Wethered |
Q: When starting the boat for the 1st time this year an alarm sounds. Last year the dealer said it was ...
A: the alarm also sounds due to the automatic oil blend system. You distinguish the problem by ...
|
| 5.0 Merc cruser | 5/13/2008 | chris Wethered |
Q: 5.0 L-220 HP Mercruser I need the location of the Blue Drain Plugs. Thanks
A: sorry for the late response. I believe the blue drain plugs for your model are located either ...
|
| pull rope is tight | 5/13/2008 | chris Wethered |
Q: i bought a 9.9 that was just rebuilt. thats what i was told i haven't tryed starting it because the ...
A: you need to remove the bolts attaching the recoil assembly and gently lift it off. Pull the ...
|
| 4.5 mercury | 5/12/2008 | chris Wethered |
Q: I have a 4.5 hp 1985 mercury,cleaned the carb, replaced the points, but will still not idle. I had ...
A: Coil Checking remove the spark plug caps and measure the resistance between the high tension wires. ...
|
| flywheel 30hp mariner | 5/12/2008 | chris Wethered |
Q: flywheel keeps coming loose what do i do
A: i believe your magnets are the reason for the flywheel coming loose: Get a magnet glue kit - 2 part ...
|
| won't start | 5/12/2008 | Everett Peacock |
Q: I just bought a 1988 Thompson 24 FT. I can't get it to turn over with the ignition however it will ...
A: it sounds like a solenoid..you should have 12 volts to one of the small wires connected to the ...
|
| outboard motor | 5/11/2008 | chris Wethered |
Q: what is the procedure for installing a new water pump impeller in my 90's 25 hp yamaha outboard
A: use your manual if you've got it, but here are some instructions to follow for replacing the ...
|
| Mercury 225 EFI Leaking Gear Oil From ... | 5/11/2008 | chris Wethered |
Q: It looks to me like my engine is leaking gear oil from the joint between the lower unit and power ...
A: Check the seals to find which one is causing the leak If you find the seals are the problem, ...
|
| my 1989 bayliner force engine is idling high | 5/11/2008 | chris Wethered |
Q: i just purchased the boat : bayliner capri bowrider 4 cylinder force engine, i thought the engine ...
A: The light smoke is fine as long as it is not dark and goes away after a short period. If the gas / ...
|
| Mercury Outboard flooding | 5/10/2008 | chris Wethered |
Q: Wethered, My husband has a Mercury outboard motor. It started flooding. We were out fishing and on ...
A: your the first person to call me that! What you need to do is clean the carburetter with spray ...
|
| motor mount floor repair | 5/10/2008 | Everett Peacock |
Q: 1986 wellcraft aft cabin with merccrusier 350 right side floor motor mount is not holding floor ...
A: you can remove or replace the mount but when you are done you have to realign the engine with the ...
|
| OMC runs rough! | 5/10/2008 | Everett Peacock |
Q: I have a 1989 OMC Cobra, 351 5.8L, Ran great everytime before, sat for a winter and wouldn't start. ...
A: you should replace the condensor when replacing the points... and make sure they are gapped ...
|
| tilt/trim wiring | 5/10/2008 | Everett Peacock |
Q: I have a 1983 4 Winns with a Mercruiser 470 in/out. The wiring to the trim sensors failed. ...
A: First of all, the trim sensor is seperate from the trim motor wiring..one side of the gimbal ...
|
