Mast (sailing)
The
mast of a sailing ship is a tall vertical pole which supports the
sails. Larger ships have several masts, with the size and configuration depending on the style of ship.
Until the 20th century, a ship's masts would be wooden
spars, originally constructed from a single straight tree trunk. As ship sizes increased, taller masts were constructed by lashing up to three spars together.
A
ship's masts are named from bow to stern (front to back):
*
Fore-mast - the first mast, or the mast fore of the main-mast.
**Sections: Fore-mast lower — Fore topmast — Fore topgallant mast
*
Main-mast - the tallest mast, usually located near the centre of the ship.
**Sections: Main-mast lower — Main topmast — Main topgallant mast
*
Mizzen-mast - the third mast, or the mast immediately aft of the main-mast. Typically shorter than the fore-mast.
**Sections: Mizzen-mast lower — Mizzen topmast — Mizzen topgallant mast
*
Jigger-mast - the fourth mast, although ships with four or more masts were uncommon, or the aft most mast where it is smallest on vessels of less than four masts.
**Sections: Jigger-mast lower — Jigger topmast — Jigger topgallant mast
Mast names for other vessels generally follow this naming.
Many ships would also have a
bowsprit at an angle closer to the horizontal extending forward of the
prow.
Most types of ships with two masts would have a main-mast and a smaller mizzen-mast, although both
brigs and two masted
schooners instead carry a fore-mast and main-mast. On a two-masted vessel with the mainmast forward and a much smaller second mast, such as a
ketch, or particularly a
yawl, the terms
mizzen and
jigger are synonymous.
Some two-masted schooners have masts of identical size, but the aftmost is still referred to as the main-mast, and normally has the larger
course. Schooners have been built with up to seven masts in all, with several six-masted examples.
On
square rigged vessels, each mast carries several horizontal
yards from which the individual
sails are hung, see also
rigging.
Although sailing ships had been superseded by engine powered ships in the
19th century, recreational sailing ships and yachts continue to be designed and constructed. In the
1930s aluminium masts were introduced on large
J-class yachts. Aluminium has considerable advantages over wooden masts, being lighter, stronger and impervious to rot. Also aluminium mast could be extruded as a single piece for the entire height as the mast.
After the
Second World War, extruded aluminium masts became common on all
dinghies and smaller yachts. Higher performance yachts would use tapered aluminium masts, constructed by removing a triangular strip of aluminium along the length of the mast and then closing and welding the gap.
|
Illustration of modern mast and wing-mast cross-sections, with sail. |
From the mid
1990s racing yachts introduced the use of
carbon fibre and other
composite materials to construct masts with even better strength to weight ratios. Carbon fibre masts could also be constructed with more precisely engineered aerodynamic profiles.
Modern masts form the leading edge of a sail's
airfoil and tend to have a teardrop-shaped cross-section. On smaller racing yachts and catamarans, the mast rotates to the optimum angle for the sail's airfoil. If the mast has a long, thin cross-section and makes up a significant area of the airfoil, it is called a wing-mast; boats using these have a smaller sail area to compensate for the larger mast area.
*
Sailing ship*
Rigging*
Sail-plan*http://www.bluewatersailing.com/shipclass.php
*http://www.hms-trincomalee.co.uk/virtual/rigging/sails.htm
*http://tallships.sailtraining.org/sailrigs.htm
*http://boatdesign.net/articles/mast-materials/
*
Glossary of Nautical terms, sailing and boat parts
